Here, The Course Note and syllabus of Microprocessor at the 3rd semester of the Diploma in Computer Engineering/IT CTEVT.
![[PDF] Microprocessor - 3rd Semester Note & Syllabus CTEVT | Diploma in Computer Engineering/IT](https://blogger.googleusercontent.com/img/b/R29vZ2xl/AVvXsEgY9mXyq9hgbbtct5nl6guqxRSSX4L8ifUIhBwf2qsQ9NcI_IuYPQ4w3mpjCDj1hv2m_oF6NG7Nkk0KNv96wQspHVduKi-4PQ-r9nsADUyYDwbLhqduuzHLR8wqqRhZO1w8p0k2l3cwvZM/s280/Microprocessor.png "[PDF] Microprocessor - 3rd Semester Note & Syllabus CTEVT | Diploma in Computer Engineering/IT")
![[CTEVT] 2nd Year 1st Semester Microprocessor | Course Note/Syllabus | Diploma in Computer Engineering/IT](https://blogger.googleusercontent.com/img/b/R29vZ2xl/AVvXsEhbqrUgFnfvRXcX_wf2xe3ZzkJJquYINDdkaliGo1m052oaY5er9oRAnO7UAm2ZnstcUpuT4Sv3B2adstqKi3DPXTNpH5PgMU1m7wI4_DB3wKf4hiBAy_pG1wHcidwsm27-rsZO24szldE/w320-h93/download.jpg "[CTEVT] 2nd Year 1st Semester Microprocessor | Course Note/Syllabus | Diploma in Computer Engineering/IT")
Microprocessor
EG 2107 EX
Total: 7 hour /week
Year: II Lecture: 3 hours/week
Semester: III Tutorial: 1 hours/week
Practical: 3 hours/week
Course Description:
This course deals with fundamentals of microprocessor, basic low level microprocessor programming, interfacing and
introduction to basic programmable devices.
Course Objectives:
After completing this course the students will be able to:
1. Explain the working principle of a
computer
2. Demonstrate the working principle
of microprocessor
3. Implement the process of writing and executing low level language
4. Explain and implement the Interfacing techniques of devices
with a computer system
Course Contents
|
Units |
Topic |
Contents |
Hours |
Methods/ Media |
Marks |
|
1 |
Introduction to Microprocessor: |
1.1 History of computer development 1.2 Analog and
digital computer 1.3 Microprocessor, microcomputer, microcontroller 1.4 Stored program concept and von-Neumann’s architecture 1.5 General architecture of a microcomputer system showing
control buses 1.6 History of x86 microprocessors 1.7 Block diagram
of a typical microprocessor
and microcontroller 1.8 Programming language 1.9 Instruction set of
microprocessors 1.10 Introduction to Simple as Possible (SAP1, SAP2, SAP3)
computers |
[8] |
|
|
|
2 |
Microprocessor architecture and |
2.1 Internal architecture of 8085 microprocessor 2.2 Instruction and
data formats |
[8] |
|
|
|
|
the instruction set: |
2.3 Instruction classifications 2.4 Addressing modes in 8085 2.5 8085 Instruction set |
|
|
|
|
3 |
Assembly language programming for 8085 |
3.1 Introduction to assembly language and assemblers 3.2 Simple assembly language programs 3.3 Programs using
loops, counters, delays 3.4 Table processing 3.5 Subroutine and
stack 3.6 Code conversion ASCII/BCD/Binary |
[9] |
|
|
|
4 |
Interfacing I/O and
memory devices: |
4.1. 8085 machine cycles and
bus timing · Fetch and execute cycles · Memory read/write machine cycle ·
I/O read/write machine
cycle 4.2.
Address Decoding · Unique and non-unique address decoding · Address decoding for I/O and
memory devices 4.3. Interfacing I/O devices · Interfacing Input
Devices ·
Interfacing Output Devices · Address decoding using
block decoders · Interfacing
Memory-mapped I/O 4.4. Memory Interfacing · Memory structure and its requirement · RAM and ROM chips · Address
decoding using NAND and block decoders 4.5. Direct memory
access |
[10] |
|
|
|
5 |
8085 Interrupt processing: |
5.1.
Programmed I/O 5.2. Interrupt Driven
I/O 5.3. The 8085 Interrupt 5.4. 8085 Vectored Interrupts 5.5.
Restart and software instructions |
[6] |
|
|
|
6 |
Introduction to
general purpose |
6.1. 8255 Programmable Peripheral Interface |
[4] |
|
|
|
|
programmable peripheral devices: |
6.2. 8254(8253) Programmable Interval Timer 6.3. 8259 Programmable Interrupt Controller 6.4.
8251 USART |
|
|
|
|
Practical: |
[45 hrs] |
|
|
||
|
Perform the
following tasks: |
|
|
|
||
|
1.
Demonstrate the basics
of microcomputer system
through the 8085 microprocessor trainer
kit 2.
Write a program that uses data transfer instructions 3.
Write a program
that uses arithmetic instructions 4.
Write a program
that uses logical instructions 5.
Demonstrate with conditional and unconditional branching 6.
Demonstrate with conditional and unconditional subroutine call
and stack 7.
Demonstrate involving loops
and counters 8.
Demonstrate that involves masking and checking numbers 9.
Write a program to manipulate table of numbers 10. Write a program
for BCD and ASCII manipulation 11. Write a program to perform multiplication and division 12.
Write a programs to read and write
from the port |
|
|
|
||
Reference books:
1. Ramesh S. Gaonkar, “8085 Microprocessor programming and interfacing”, New Age
2. John Uffenbeck, “The 8080, 8085 & Z-80 Programming, Interfacing and Troubleshooting”, PHI
3. B. Ram "Fundamentals
of Microprocessor and Microcontrollers" Dhanpat Rai Publications
4. Ajay Wadhwa, "Microprocessor 8085:
Architecture, Programming and Interfacing", PHI
5. Albert Paul Malvino, Jerald
A. Brown, “Digital
Computer Electronics”, McGraw-Hill
